Customer service Tel: +45 31 20 78 74 | Order today – we send the goods tomorrow !

Customer service Tel: +45 31 20 78 74
Order today – we send the goods tomorrow !

u

Where can the tiles be used?

The tiles can be used everywhere, except in a wet room (the shower), on the floor or outside
u

How big is each tile and what is the total thickness (incl. mounting plate)?

Click’n Tile tiles are available in two variants. A 10 × 10 cm tile and the metro tile which is 13.3×6.6 cm tile. The thickness of the tile including mounting plate and adhesive is approx. 8.2 mm.
u

Can you mix 10x10 and the metro tile?

You can easily do that. In length, 3 metro tiles correspond with 4 10×10 tiles and in height 5 metro tiles correspond with 4 10×10 tiles.
u

Can the mounting plate be glued on top of ordinary tiles?

Yes, the mounting plate can be glued to glazed tiles, raw tiles, wood, painted, plastered, felted and raw walls. The only thing to be sure is that the underlayer is bearing (not loosely mounted) and clean. Remember, the result is best if the bottom layer, on which the mounting plate is glued, is strong.
u

How to remove excess glue?

If you want to remove the mounting plate, the glue is likely to remain on the wall. The glue can be removed with a knife, after which the wall should be filled and painted.
u

Can the backplate be fitted with double-sided tape?

You can do this well and you can buy the tape in our webshop.

The “weak element” of double-sided adhesive tape is not the tape, but rather the surface of the wall. We therefore recommend when mounting on a painted wall that you also staple the mounting plate to the corners with a staple gun.

u

What to do with grout?

Click’n Tile are without joints, which makes them easy to remove. If you look at the tiles from the side, you will see that they are close to the mounting plate, but also that there are 1.2 mm slots in the top.
u

Can Click'n Tile be used in a food company?

Yes, but since the Danish Veterinary and Food Administration requires that “The walls in production rooms or areas should be covered with a smooth material that is waterproof and washable”, the crack between the tiles must be filled with sanitary silicone or epoxy joint.
u

How do I wash the tiles?

With ordinary universal detergent. It is not recommended to use abrasive as it will polish the surface.
u

Can I put the tiles in the dishwasher?

Yes, but only if the temperature is below 42 degrees. Alternatively, we recommend putting them in a pillowcase and washing them in the washing machine at 30-40 degrees.
u

Can the tiles withstand heat from our hobs?

Yes, they can. If you have gas hobs, make sure that there is a minimum of 3 cm from the edge of your gas hobs to the tiles.
u

How about lime?

If you use the tiles where there is lime, then we recommend that you have a small atomizer where you have mixed lemon cleanser 1:10 with water. However, the mixing ratio is dependent on the detergent. When you then want to clean the tiles, it is done simply by using the nebulizer. This allows the detergent to work while also being better for the environment.
u

How can I cut the tiles?

With a regular 10 cm cutting box and if you have to cut many tiles then you can also use a jigsaw, circular saw or cutting / fermenting saw.
u

What are the tiles made of?

The tiles are made of ABS plastic (the same plastic that is used for LEGO bricks), and since ABS plastic has the fantastic property that it can be recycled, we have established a return system where you can get a mortgage for your excess tiles.
u

How stable are the colors?

In our test, we have not seen that the colors change color over time, but theoretically it could happen. In addition, there may be minimal color variations from batch to batch.
u

What do I do if there is an electrical wall-outlet?

Disconnect the power cord and secure the cables, glue the mounting plate on top, and cut out the hole. The tiles are cut before the socket can be reassembled. A small idea is that you screw the socket or switch to the wall or front box with switch screws. Please note that only an authorized electrician may disconnect/replace an electrical power outlet, and the outlet can be located on the outside of the tiles.
u

Can you hang shelves or hooks on the Click'n Tile wall afterwards?

Yes, of course, just remember to drill a small hole in the tile and mounting plate and that the screw should stick to the back wall.
u

How long does it take to assemble?

Mounting plate is available in two variants 90×60 cm and 180×60 cm. It takes about 15-30 minutes to mount a mounting plate. The plastic tiles take no time, but it is also here that you get to play with the look of your wall. If cutting the tiles is required, this will take approx. 2 minutes per tile depending on whether you use a cutting box or a saw.
u

How many tiles should I order?

Calculate your area. The small mounting plate is 0.54 m2 and the large 1.08 m2. For every 1 m2, 100 pcs. 10×10 tiles or 120 pcs. metro tiles and 0.5 l glue.
u

What if the wall is felted or plastered?

If the wall is felted or plastered, then you must first prime the wall with wall primer also called plaster foundations. Wall primer provide optimal adhesion and give the surface a uniform absorbency.
u

Can you print on the tiles?

Yes, you have the opportunity to have your personal designs printed on the tiles. You can see the prices in the “How to do” tab on the website under “Print on tiles” section. Please send an email to LTH@clickntile.com, who will guide you through the entire process.
u

What should I do if I am a little unsure of how to do?

We have created a YouTube Playlist, where we go through the assembly process step by step. We can really recommend it. If you still have questions, you are welcome to contact Lars Thomsen by email LTH@clickntile.com. Every question we get, we also learn something from.